Robobrew

Showing all 9 results

  • Robobrew All Grain Brewin..

    Robobrew All Grain Brewin..

    $319.99

    There is no easier way for homebrewers to get directly into all-grain brewing than the new Robobrew. It is really intuitive to use and included directions and multiple online videos brewers help make it easy to learn. Because it is electric and runs on 110v power it is an easy plug and brew solution. Pair it with a $100 fermentation kit and you have a great direct to all-gain starter kit.

    Dual heating elements run off of a single 110 volt plug and have individual switches allowing for more control over the heating process. One element is 1000 watts and the other is 500 for a combined 1500 watts! Use both when you need to ramp up the temperature quickly either at the start to get to your mash temp or to go from your mash temp to boiling. Use only one of the elements when you want to hold a temperature.

    Also included is an on-board water resistant control panel for setting and monitoring temperatures. You can also set a delayed start of up to 23 hours in advance so that you can have your water hot and ready to go when you get home from work or get up in the morning.

    The brewery also includes a removable stainless steel malt pipe with false bottom allowing you to easily shift from mash tun to boil kettle during your brew day. The malt pipe includes a handle to lift it from the RoboBrew and tabs at the base so you can set the malt pipe over the RoboBrew to let the wort drain out. It also has feet at its base to raise the malt pipe slightly off the base and help prevent clogging.

    There is also a verion with the pump. While most may opt for that, this pump-less model is really extra simple to use and the efficiency is still amazingly good.

    Note: The manual references an element for a different market. This unit comes with a two heating elements for a total of 1,500 watts.

    Features:

    Stainless steel 1/2 in ball valve
    Immersion wort chiller included
    Digital temperature controller
    Stainless steel malt pipe
    Dual heating elements (1000 watts and 500 watts)
    Recommended max. grain bill – 18 lbs
    Recommended min. grain bill – 8 lbs
    110 volt plug
    21.625 in H x 12.5 in D
    You might also want:
    2′ of 1/2″ ID Silicone tubing for draining.
    To connect included Chiller: 20′ of 1/2″ ID tubing, 3 small hose clamps and 1 brass hose thread by 1/2″ barb adaptor.

    Quick View
  • Robobrew V3 All Grain Bre..

    Robobrew V3 All Grain Bre..

    $479.99

    All in one brewing systems with recirculating pumps are where it’s at. They make brewing simple and easy and get homebrewers doing all-grain earlier, many starting with their very first batch. The Robobrew is going to lead the charge with its amazing price point.
    The new version 3 of the Robobrew on Presale! If you order now it will ship in late May.It now lets you set up to 6 different times and temperatures so you can do a fully automated step mash!

    The Robobrew is an all-in-one electric brewing system that has built in elements for heating and boiling, a built in pump for recirculation, an onboard water resistant control panel for setting and monitoring temperatures, a removable grain basket, and a built in spigot for transfering. It is extremely portable and uses 110v power so it can be used nearly anywhere.

    Built in magnetic drive pump to easily recirculate the wort during the mash. We recommend getting some silicone tubing to go with the recirculation arm. This allows you more control over the recirculation and you can then use the pump to transfer your wort to your fermenter.

    Dual heating elements run off of a single 110 volt plug and have individual switches allowing for more control over the heating process. One element is 1000 watts and the other is 500 for a combined 1500 watts! Use both when you need to ramp up the temperature quickly either at the start to get to your mash temp or to go from your mash temp to boiling. Use only one of the elements when you want to hold a temperature.

    The digital control panel makes it easy to see the current temperature and set the temperature you want. You can also set a delayed start of up to 23 hours in advance so that you can have your water hot and ready to go when you get home from work or get up in the morning. The digital controller is also water resistant so don’t worry about spills or some water dripping down the side. This controller is built for brewing!

    The brewery also includes a stainless steel malt pipe with false bottom allowing you to easily shift from mash tun to boil kettle during your brew day. The malt pipe includes a handle to lift it from the RoboBrew and tabs at the base so you can set the malt pipe over the RoboBrew to let the wort drain out. It also has feet at its base to raise the malt pipe slightly off the base and help prevent clogging.

    The included stainless wort chillers is shipped with bare ends so you can set it up for your situation. We list below the most common tubing and fittings sold to help connect to a hose, hose bib, or faucet.

    Note: The manual references an element for a different market. This unit comes with a two heating elements for a total of 1,500 watts.

    Features:

    Stainless steel construction
    9 gallon total capacity with a finished beer output of 5-6 gallons
    Digital temperature controller
    110v power and plug
    Dual heating elements for total control (1000 watts and 500 watts)
    Stainless steel 1/2 in ball valve for draining (don’t have to use the pump)
    Immersion wort chiller included
    Stainless steel malt pipe/basket
    Stamped volume markers
    Glass lid
    Magnetic drive pump for recirculation
    Recirculation arm
    Temperature reads in °F or °C (press and hold temp button for several seconds to adjust)
    32.75 in H (with recirculation arm) x 12.5 in D

    You might also want:
    2′ of 1/2″ ID Silicone tubing for sparging and draining.
    To connect includedchiller: 20′ of 1/2″ ID tubing, 3 small hose clamps and 1 brass Garden Hose Thread by 1/2″ barb adaptor.

    Quick View
  • Replacement Silicone Seal..

    Replacement Silicone Seal..

    $2.99

    Silicone seal replacement for the 35 L Robobrew malt pipe

    Quick View
  • Replacement SS Immersion ..

    Replacement SS Immersion ..

    $44.99

    This is the stainless steel immersion chiller that comes with the 35 L Robobrew. Use with D1710 1/2″ ID beverage tubing.

    Quick View
  • Replacement Valve for Rec..

    Replacement Valve for Rec..

    $9.99

    Replacement recirculation arm valve for 35 L Robobrew with pump

    Quick View
  • RoboJacket – Neopre..

    RoboJacket – Neopre..

    $18.99

    Thick neoprene jacket for the 35 L Robobrew.

    Quick View
X